ABS Module Lab

00668

ABS / stability-control fault code, listed for 2 vehicle lines from Audi, Volkswagen. What it means on each one, from published sources, and when the module is the cause.

What 00668 means, by vehicle

Makers reuse code numbers, so the meaning is listed per vehicle line, as its published source states it. Neutral sources (government records, parts catalogs, technical references) are linked; other sources stay on file.

VehicleMeaning of 00668Source
2006-2013 Audi A3 (8P)Supply Voltage Terminal 30: Implausible Signalon file
2006-2018 Volkswagen Golf / Rabbit / GTI / Golf R (Mk5-Mk6)Supply Voltage Terminal 30: Implausible Signalon file

Vehicles and units that set 00668

The unit family decides the price and what ships; the part-number count is how many numbers for that line are on file for the lookup.

VehicleYearsABS unit familyRepairPart numbers
Audi A3 (8P)2006-2013ATE / Continental MK60 / MK61From $4992
Volkswagen Golf / Rabbit / GTI / Golf R (Mk5-Mk6)2006-2018ATE / Continental MK60 / MK61From $49916

What is published about failures on these lines

Is 00668 the ABS module?

00668 is listed for 2 vehicle lines from Audi and Volkswagen; the meanings above fall under the “Supply voltage to the module” family of codes.

This family of codes means the voltage reaching the ABS module was outside the range it works in — too low during cranking or with a weak battery, too high from a charging fault or a jump-start done wrong, or dropping out through a corroded feed. The module records it and switches itself off until the next key cycle. A supply code describes the vehicle’s electrical system as the module sees it; the module itself is one possible cause, when its own power stage or connector is at fault.

Is the module the likely cause? Sometimes

For this family of codes the module is one possible cause among several. A supply code is set by whatever the module measures at its own power pins. A battery near the end of its life, a slipping belt, a corroded battery terminal or ground strap, or a power pin that heats up under load sets it from outside. The module is the cause when the voltage at its connector is correct under load and the code still sets, which points at its internal power supply or a cracked solder joint on a power pin.

Check these first

In order. The first three are the same for every ABS code; the rest are for this family. Each step is something a shop or a careful owner can do before any module comes out.

  1. Load-test the battery and measure the charging voltage; a weak or over-charging supply sets codes in every ABS family and is the cheapest thing to rule out.
  2. Check the fuses that feed the ABS module and its pump with a meter, not by eye, and clean and tighten the module’s ground strap and main power feed.
  3. Unplug the module connector and look at both halves for corrosion, water, a pushed-back or bent pin; then clear the code and note whether it returns at once, after a drive, or only under one condition.
  4. Measure voltage at the module’s power pins with the key on and while cranking, and compare it with the battery — a difference under load means resistance in the feed, fuse box or connector.
  5. Check the fuse-box terminals for heat marks; a fuse holder that has overheated drops voltage under the pump’s load.
  6. Ask when the code first appeared — right after a jump-start, a battery change or welding on the vehicle points at an event, not a fault, and the code may not return.
  7. If the voltage at the module connector is correct under load and the code keeps returning, stop there: the module’s internal power stage is the remaining suspect.

What the lab does for a code in this family

At the bench we run the module from a controlled supply, test it at the low and high ends of its range and under the pump’s load, and repair the internal power supply, the power-pin solder joints and the components that fail from an over-voltage event. A repaired module will not survive a charging fault that is still on the vehicle.

Every repair is bench-tested and ships back with your VIN and coding on it. Sensors, switches, plug-in relays, wiring, fuses, the battery and the other modules are vehicle-side parts: a repaired module does not fix those, which is why the checks come first.

Repair options for these vehicles

Related codes

Codes listed for the same vehicle lines — the ones a scan tool tends to show next to 00668.

00668 — questions

What does 00668 mean on a Audi?

On the Audi line in our data, 00668 is listed as: Supply Voltage Terminal 30: Implausible Signal. In general terms it belongs to the “Supply voltage to the module” family — battery or ignition voltage at the ABS module reads too low or too high. Volkswagen lists the same number with its own wording — see the meaning-by-vehicle table.

Can I drive with 00668?

A supply fault switches ABS and stability control off, and the same weak battery or charging fault can leave you stranded. Fix the electrical cause first; if the red brake warning light is also on, have the vehicle checked before driving it. That is general guidance for this family of codes, not a judgment of your vehicle, which we cannot make from a code.

Is 00668 the ABS module or a sensor?

For this family of codes the module is one possible cause among several. A supply code is set by whatever the module measures at its own power pins. A battery near the end of its life, a slipping belt, a corroded battery terminal or ground strap, or a power pin that heats up under load sets it from outside. The module is the cause when the voltage at its connector is correct under load and the code still sets, which points at its internal power supply or a cracked solder joint on a power pin.

How much does it cost to fix 00668?

Repair of your own module starts at $499 for the vehicles that set 00668; a refurbished unit of the same family with your data cloned onto it starts at $950. Return shipping starts at $29.95 and the label to us is prepaid; rush repair is +$100 for 2–3 business days on the bench; every repair and refurbished unit carries a 1-year warranty, from the day we ship it back. Starting prices. If the bench finds more work than your service covers, we tell you the cost and you approve it before we do it.

Will 00668 clear after the repair?

A repaired module comes back tested on the bench with your VIN and coding on it; after installation the code is cleared with a scan tool. Some vehicles still need a brake bleed, initialization or calibration after install. If the cause was on the vehicle side — a sensor, the wiring, the battery or another module — the code returns until that is fixed, which is why the checks above come first.

Which vehicles set 00668?

In our data 00668 is listed for 2 vehicle lines from Audi and Volkswagen: 2006-2013 Audi A3 (8P), 2006-2018 Volkswagen Golf / Rabbit / GTI / Golf R (Mk5-Mk6). The same number can mean something different on each make, so the table above gives the meaning per vehicle.

Still not sure?

Send us 00668, a photo of the module label and your VIN — we tell you whether the module is the likely cause and what it costs, before you pull anything. Asking costs nothing.

Repair guides

The lab

ABS Module Lab

1168 W Pioneer Parkway
Arlington, TX 76013

View on Google Maps

Mail-in only — ship your module to the address in your order e-mail, not to the bench.

00668 keeps coming back after the checks? Fix the module — from $499.

Look up your part number and order online — we email you a prepaid label to our lab. Or send us a photo of the label and your VIN first, and we'll tell you what you have and what it costs.

Back with your VIN and coding · can’t be repaired? repair price back, minus shipping and a $150 bench evaluation fee · 1-year warranty · rush 2–3 days +$100

Call (817) 505-4201 · 📱 Text us a photo of the module label · Confirm my module first — free · Email repairs@absmodulelab.com