VW and Audi ATE MK60 ABS Module: Codes 01276 and 16352 Repair Guide
ABS Module Lab Team · · updated · 16 min read
Which VW and Audi models carry the ATE MK60 / MK61 ABS unit, what codes 01276 and 16352 mean, and what a repair, refurbished or new module costs.

On the 2006–2018 Golf, Jetta and GTI and the 2006–2013 Audi A3, the ATE MK60 or MK61 ABS unit fails inside the control unit bolted to the hydraulic block, and a VW/Audi scan tool reports it as 01276 (the pump, V64) or 16352 (control module faulty). A component-level repair of your control unit starts at $499, coding kept; a refurbished unit written with your data starts at $950; a new unit from the dealer has to be coded to the car, and our data holds no list price for one. The control unit unbolts from the block, so the brake lines can stay closed.
Which VW and Audi models have this ABS unit
The MK60 and MK61 are Continental Teves (ATE) ABS / ESP units: a pump motor, a valve block and a control unit screwed onto the block over the valve coils. Volkswagen numbers the two halves separately: a 1K0 907 379 or 1K0 907 375 number is the control unit, a 1K0 614 517 or 1K0 614 117 number is the hydraulic unit (often with a BEF suffix, meaning sold filled), and the ATE number beside it is often quoted without its dots. All of these belong to the ATE / Continental MK60 / MK61 family.
Golf, Rabbit, GTI, Golf R, Jetta, Eos and Beetle (Mk5 and Mk6)
The 2006–2018 Golf, Rabbit, GTI and Golf R carry an MK60 to about 2008 and an MK61 from 2009; the split is approximate, since the two application lists in our data overlap in 2007–2008, and the label decides. The MK60 list covers the 2006–2008 GTI, 2007–2008 Rabbit and Eos and the Jetta to 2008; the MK61 list adds the 2009–2018 Jetta, 2010–2014 Golf, 2009–2014 GTI, Eos, Beetle, 2012–2019 Passat, Routan and 2007–2010 Touareg.
Audi A3 (8P)
The 2006–2013 Audi A3 (8P) uses an ATE MK61 and shares its 1K0 907 379 control units with the Golf; the numbers tied to the A3 in our data are 1K0907379AD and AE. The first US cars of 2006 may carry an MK60, which no source confirms, so check the label on an early car.
Passat B6 and the US Passat
The 2006–2010 Passat B6 (3C) has an integrated ABS / ESP unit under 3C0 614 109 whose supplier is not verified in our data. The US-built 2012–2019 Passat is on the MK61 list, which is why the line sits in this family; a B6 owner should photograph the label before ordering.
Golf, Jetta, New Beetle (Mk4) and Audi TT (8N)
The 1998–2006 Golf, GTI, Jetta and New Beetle (Mk4) started with an ITT / ATE MK20 (Mk20 IE) on cars without ESP and moved to an MK60 on later cars with ESP; the catalog files the line under the ATE MK20 family, but an ESP car from this generation is an MK60 job, with 1C0 907 379 control units (in the table below); 1C0907379K is the genuine non-ESP module. The 2000–2006 Audi TT (8N) is listed with an MK20 for the 2000–2002 cars without stability control; later and DSC-equipped TTs probably use a different unit (one source attributes 16352 on the TT to an MK61), so the label decides.
Audi A4: Bosch, not ATE
If you own an A4, your unit is Bosch and the MK60 pages do not apply. The 1998–2003 A4 and S4 (B5) has a Bosch 5.3 in the Bosch 5.3 family. The 2002–2008 A4, S4 and Cabriolet (B6, B7) is listed with a Bosch 5.7, and the B7 also appears under Bosch 8.0 from 2005; the catalog files that line in the Bosch 8 family, the Bosch 5.7 page covers the earlier units, and the label decides which you have. The 2008–2012 A4, S4 and Avant (B8) has a Bosch 8.0, and the 2016–2020 A4, A4 allroad and A5 (B9) has a Bosch 9.0 in the Bosch 9 family. The 1998–2005 Passat B5 is Bosch too, 5.3 to about 2002 and 5.7 after.
What moved on to MK100
Two lines in our data left this generation for the Continental MK100: the 2015–2020 Audi A3 and S3 (8V), a 46-pin MK100 under 5Q0 and 8S0 numbers shared with VW's MQB cars, and the Tiguan (5N) from 2018, both on the MK100 family page. Our sources say nothing about an MK70 on these models.
Symptoms of a failing ABS module on these VW and Audi models
The yellow ABS lamp and the ESP or traction triangle come on together, sometimes with the red brake warning as well. The first appearance is often intermittent, lit for a drive and gone after a restart, before the lamps stay on.
A speedometer that stops working is listed for the MK60 on the Golf, Jetta and Beetle and for the TT module, because the wheel-speed signal to the cluster passes through the ABS control unit.
The ABS pump not working is the symptom behind 01276. The pump may be silent during the self-test, run briefly and stop, or run when it should not.
With ABS and ESP off the base brakes work, but the wheels can lock in a panic stop and nothing corrects a slide.
The fault codes you will see
VW and Audi scan tools report ABS faults as five-digit VAG codes, sometimes with a sub-code after a colon; the Bosch rows are marked because an A4 owner meets different numbers.
| Code | Meaning | What it points to |
|---|---|---|
| 01276 | ABS Hydraulic Pump (V64): Signal Outside Specifications / Electrical Fault in Circuit / Implausible Signal (Golf Mk4 to Mk6, TT 8N) | The pump motor or its driver stage; on the Golf, Jetta and Bora (1J/9M) check the fuse panel on top of the battery first |
| 16352 | Control Module Faulty: Electrical Error; an internal failure within the ATE MK61 control unit (Golf Mk5, A3 8P, TT 8N) | The control unit itself |
| 01316:013 | ABS Control Module: No Signal / Communication (Golf Mk5–Mk6, A3 8P) | Stored by other modules when the ABS control unit goes quiet: a dead unit or a dead feed |
| U101700 | ABS Control Module Communication (Golf Mk5–Mk6, A3 8P) | The same loss of communication in SAE format |
| 01130 | ABS Operation: Implausible Signal (Golf Mk4–Mk6, A3 8P); causes include a faulty control module J104; clears only after a drive above 20 km/h | The control unit, once wheel-speed causes are ruled out |
| 00668 | Supply Voltage Terminal 30: Implausible Signal (Golf Mk5–Mk6, A3 8P) | Battery, charging, fuses and the feed to the unit before anything inside it |
| 00283, 00285, 00287, 00290 | Wheel Speed Sensor: Implausible Signal, one code per wheel, left and right, front and rear (Golf Mk5–Mk6) | A sensor, its wiring or its ring; all four at once points at the control unit |
| 01418, 01421 | Switch valve 1 and high pressure valve 2 (A4 B8, Bosch 8.0) | Valve drivers in the Bosch control unit |
| C123EF0 | Hydraulic Brake Booster Limit Value Reached (A4 B9, Bosch 9.0) | The Bosch 9 unit's booster function |
When the scan tool cannot reach the ABS control unit at all, the engine and instrument modules store 01316:013 or U101700 and the ABS address answers nothing: either a failed control unit or no power to it. Prove battery voltage and ground at the ABS connector with a meter before deciding the unit is dead.
Why these modules fail
The documented fault behind 16352 is an internal failure of the ATE MK61 control unit, and the sources describe the broader pattern as faults in the ABS motor, block and pump, caused by internal component breakdown; the MK60 notes add loss of communication and a dead speedometer.
On the bench that breakdown takes two forms we test for: the pump-motor power stage fails or its connection opens (01276), or the processor or power-supply section stops responding (16352, 01316:013 or U101700, and 01130 when the unit is half alive). Heat cycling and vibration open the connections between the board and the coil and motor pins. A component-level repair rebuilds those connections and replaces the failed parts, and the unit keeps its coding because nothing is erased.
What is not the control unit matters just as much:
- The pump motor itself can wear out or seize. It sets 01276 too, and the bench tells motor from driver by running the motor under load.
- The fuse carrier on top of the battery carries the ABS feeds; damage there is the first thing the diagnostic-tool maker's notes say to check for 01276 on the Mk4, with a healthy control unit behind it.
- Low system voltage sets 00668; a tired battery, a weak alternator or a corroded ground is the cause, not the unit.
- A wheel-speed sensor, its wiring or a damaged ring sets one of 00283 to 00290 for that wheel; four at once is a control-unit problem.
The Bosch A4s fail in their own ways: loss of communication, pump or solenoid failures, wheel-speed and brake-pressure-sensor codes on the 5.7 and 8.0, and C123EF0 or an ABS valve supply voltage circuit open on the B9's 9.0; those repairs are priced on their own family pages.
Check these before you condemn the module
A VAG-capable scan tool and a meter cover all of this.
- Battery and charging. Low voltage is the cheapest explanation for 00668; charge or replace the battery, clear the codes and drive first.
- The fuse carrier on the battery. Look under its cover for melted plastic, corrosion or a loose nut on the heavy feeds; on the Mk4 it is the first check for 01276, and worth a look on later cars.
- Grounds. Clean the engine-to-body and battery-to-body grounds and the ABS ground point to bare metal.
- The ABS connector. With the battery disconnected, unplug it and look for corrosion, spread terminals or moisture.
- Wheel-speed live data. Graph all four speeds at walking pace. One wheel reading zero or lagging is a sensor, wiring or ring problem; four clean traces with a pump or control-module code put the fault in the unit.
- The communication test. Key on, back-probe the terminal 30 and 15 feeds and the ground at the ABS connector; voltage present with no answer at address 03 confirms the control unit.
- The 01130 test drive. This code clears only after a drive above 20 km/h; a code that reappears without that drive has not been tested yet.
- Coding. If a used unit was recently fitted, compare its coding with the original; the diagnostic-tool maker's wiki recommends reusing the original coding, and a mismatch mimics a hardware fault.
When the lamps are on with 16352, 01276 or a communication fault, voltage is proven at the connector and the wheel speeds are clean, the control unit is the fault.
Repair, refurbished, used or new: what each really costs
All of these are starting prices and are what checkout charges; any work past what the service covers is priced and cleared with you before it starts.
| Choice | Starts at | What comes back | What the car then needs |
|---|---|---|---|
| Repair of your control unit | From $499 | The same unit, repaired at component level and tested under load, coding untouched; 1-year warranty | Refit, clear codes, a test drive above 20 km/h; a bleed solely if you opened a line |
| Refurbished unit with your data | From $950 | A unit from the same family loaded with the coding and configuration read out of yours; the original becomes the core and is not returned; 1-year warranty | Nothing extra |
| Used unit | Listings in our data run from $99.99 for a used Mk4 pump and module and about EUR 119 for a used B6 unit to $249 for a genuine non-ESP Mk4 module | A unit coded to another car, with no history; a prefix match can still be the ESP or non-ESP version | Dealer-level coding to your car, which the sellers themselves note |
| New unit from VW or Audi | No dealer list price in our data for any of these lines; ask a dealer with your VIN | A new unit with the maker's parts warranty | Dealer coding, and a bleed if the hydraulic unit is replaced |
Return shipping is on top: $29.95 standard delivery in 3–5 business days, $54.95 by UPS 2nd Day Air, $94.95 by UPS Next Day Air; the prepaid inbound label is part of the price, and an extra $55 upgrades it to UPS 2nd Day Air. Plan on roughly a week at the bench, or pay $100 for rush repair and the work is done in 2–3 business days. Coverage runs 1 year from the ship date on repairs and refurbished units alike, with the terms on the warranty page.
No advance exchange is possible, because the refurbished unit is written with data read from your original, so yours must arrive first. If the bench finds the unit past saving, you hear from us before anything else happens and pick one of two routes: a refurbished unit carrying your coding, from $950, with what you already paid credited against it and the balance confirmed with you first, or the unit back and the repair charge refunded, shipping excepted. Order from the MK60 / MK61 family page or start a repair directly; if you are not sure which unit you have, request a quote with a photo of the label.
Removing and shipping the module
On the MK60 and MK61 the control unit is held to the hydraulic block by screws and comes off with the pump-motor connection, leaving the block and its brake lines in place. Ship the control unit alone when you can.
- Disconnect the battery negative terminal and wait a minute.
- Photograph both labels: the 907 379 or 907 375 number on the control unit and the 614 517 or 614 117 number on the block, plus the ATE number.
- Remove the screws around the control unit's edge and draw it straight off the block without twisting or prying against the aluminum.
- Tape a clean bag over the block so the coils and pins stay dry while the unit is away.
- If the control unit will not separate cleanly, or the car has the integrated 3C0 614 109 unit, send a photo through the quote form first. If the whole unit must come out, mark each line to its port, cap every port, plug every line and plan on a scan-tool bleed afterwards.
- Wrap the control unit in bubble wrap with the pin face protected, box it with padding on all sides and write the RMA on the box.
- Use the prepaid label from your confirmation email. The mail-in instructions page shows the packing steps.
Brakes are a safety system; a line that has to be opened is a job for a shop.
What happens at the bench
The control unit is booked in against its RMA with both labels photographed, then clamped into a test fixture that reads its coding and fault memory and runs the pump output and each valve channel under load, which is where a weak motor driver or an open coil connection gives itself away. After the component-level repair the same run is repeated to prove it, and the unit is packed with the coding it arrived with; one that cannot be saved stops there, and you hear from us before anything else happens. The how it works page describes the sequence.
After it is back in the car
Fit the control unit squarely onto the block, tighten the screws evenly, reconnect the connector until the lever locks and reconnect the battery. If the lines stayed closed, no bleed is needed; if the hydraulic unit came out, bleed with the scan tool's ABS bleed routine so the block is purged. Clear the fault memory in the ABS control unit and in the engine and instrument modules.
Then drive the car above 20 km/h for a few minutes so the system completes its checks and 01130, if it was stored, clears. Some vehicles still need a brake bleed, initialization or calibration after install; your repaired control unit keeps its coding, so no coding visit is needed for it.
Part numbers for the VW and Audi MK60 / MK61 units
Type the control-unit number or the hydraulic-unit number into the part-number lookup, with or without spaces; the match runs on the base number, which means a suffix you have never seen still finds the family.
| Part number | Fits | Note |
|---|---|---|
| 1K0 907 379 AA | 2006–2008 GTI, 2007–2008 Rabbit and Eos, Jetta to 2008 | MK60 control unit; 1K0 907 379 AC and K on the same list |
| 1K0907379AD | Golf Mk5–Mk6 and Audi A3 8P | MK61 control unit shared by both; ATE 10096103073 |
| 1K0907379BL | Golf | ATE 10096103643 |
| 1K0-907-375-BL | 2009–2018 Jetta, 2010–2014 Golf, 2009–2014 GTI, Eos, Beetle, 2012–2019 Passat, Routan, 2007–2010 Touareg | MK61 list; -BM, -BK and -AD on the same list |
| 1K0-614-517-ED-BEF | Same MK61 list | Hydraulic unit, sold filled; -DP-BEF and 1K0-614-117-S-BEF are variants |
| 1C0 907 379 L | 2001–2010 Beetle, 2001–2006 Golf, 2001–2008 Jetta | MK60 control unit on the Mk4 ESP cars; D, M, P and Q on the same list; 1J0 614 517 M is the hydraulic unit |
| 3C0 614 109 | 2006–2007 Passat B6 and 4Motion | Integrated ABS / ESP unit; 3C0 614 109 A is the replacement number |
| 3C0614109C | Passat B6 TDI | ESP / ABS control unit and pump; 3C0614109T also seen |
FAQ
What does code 01276 mean on a VW or Audi?
01276 is ABS Hydraulic Pump (V64): signal outside specifications, electrical fault in circuit or implausible signal. The control unit cannot run the pump as expected, which is either the pump motor, the control unit's motor driver or the feed to them.
What does code 16352 mean?
16352 is Control Module Faulty: Electrical Error; on the MK61 of the Golf Mk5, A3 8P and TT 8N it indicates an internal failure within the ABS control unit, the fault a bench repair is aimed at.
How much does an MK60 or MK61 ABS module repair cost?
A repair of your own control unit starts at $499 plus return shipping from $29.95; a refurbished unit with your coding cloned onto it starts at $950. We have no dealer list price for a new unit on these cars in our data.
Do I need coding after the repair?
Not for a repaired control unit, which keeps the coding it had, and not for a refurbished unit from us, which is written with your original's data before shipping. A used or new unit does need coding to the car.
Can I drive the car while the control unit is away?
If only the control unit was removed and the lines stayed closed, the base brakes work and the car can be moved, without ABS or ESP and probably without a speedometer. If the hydraulic unit came out, the car stays parked until it is back and bled.
What if my unit cannot be repaired?
Nothing further happens until you have heard from us. Then it is your call: a refurbished unit from the same family, your coding written into it, from $950, with only the shortfall between that and your earlier payment to settle once we confirm it, or the unit returned and the repair price refunded, less the shipping and a $150 bench evaluation fee.
What does the warranty cover?
Our work on a repaired or refurbished unit is covered for one year from the day it ships. Wheel-speed sensors, wiring, the hydraulic block and electrical damage from outside the unit are not covered, and shipping on a claim is yours both ways.
Sources
- Diagnostic-tool maker's wiki pages for the code definitions and the Mk4 brake electronics — 01276, 01130, VW Golf (1J) Brake Electronics (MK20)
- Independent rebuilders' application pages for the unit identifications, code lists and failure descriptions; a UK test house's catalog titles for the 1K0 907 379 numbers; used-parts dealers' listings for the Passat B6 and Mk4 numbers and prices; a parts seller's page for the genuine non-ESP Mk4 module (not linked).


