01421
ABS / stability-control fault code, listed for 2 vehicle lines from Audi. What it means on each one, from published sources, and when the module is the cause.
What 01421 means, by vehicle
Makers reuse code numbers, so the meaning is listed per vehicle line, as its published source states it. Neutral sources (government records, parts catalogs, technical references) are linked; other sources stay on file.
| Vehicle | Meaning of 01421 | Source |
|---|---|---|
| 2005-2011 Audi A6 / S6 (C6) | High pressure valve 2 | on file |
| 2008-2012 Audi A4 / S4 / A4 Avant (B8) | High pressure valve 2 | on file |
Vehicles and units that set 01421
The unit family decides the price and what ships; the part-number count is how many numbers for that line are on file for the lookup.
| Vehicle | Years | ABS unit family | Repair | Part numbers |
|---|---|---|---|---|
| Audi A6 / S6 (C6) | 2005-2011 | Bosch ABS / ESP 8 | From $499 | 8 |
| Audi A4 / S4 / A4 Avant (B8) | 2008-2012 | Bosch ABS / ESP 8 | From $499 | 7 |
What is published about failures on these lines
- 2005-2011 Audi A6 / S6 (C6): ABS light on, brake-pressure-sensor faults, no communication, ESP/traction light on and wheel-speed-sensor faults.
- 2008-2012 Audi A4 / S4 / A4 Avant (B8): Loss of communication, pump or solenoid failures, wheel-speed-sensor issues and brake-pressure-sensor codes for its Bosch 8.0 Audi repair
Is 01421 the ABS module?
01421 is listed for 2 vehicle lines from Audi; the meanings above fall under the “Valve or solenoid circuit” family of codes.
This family of codes names one of the solenoid valves inside the hydraulic block — an inlet, outlet, isolation, dump or traction-control valve for one wheel or circuit — or the relay that supplies all of them. The module checks each valve coil’s resistance and the current it draws when it fires; an open coil, a shorted coil, or a driver that cannot switch sets the code. The coils are inside the hydraulic unit and the drivers are inside the module, so there is little vehicle wiring in this circuit.
Is the module the likely cause? Often
For this family of codes the module is a likely cause, but not the only one. On a valve code there is almost nothing between the module and the fault: the coil is in the hydraulic block it bolts to, the driver and the valve-relay function are on the module’s board, and the connection between them is a set of spring pins or solder joints that corrode and crack. The outside causes — low supply voltage, a bad ground, a connector pin — are quick to rule out.
Check these first
In order. The first three are the same for every ABS code; the rest are for this family. Each step is something a shop or a careful owner can do before any module comes out.
- Load-test the battery and measure the charging voltage; a weak or over-charging supply sets codes in every ABS family and is the cheapest thing to rule out.
- Check the fuses that feed the ABS module and its pump with a meter, not by eye, and clean and tighten the module’s ground strap and main power feed.
- Unplug the module connector and look at both halves for corrosion, water, a pushed-back or bent pin; then clear the code and note whether it returns at once, after a drive, or only under one condition.
- Read the code’s valve position (which wheel, inlet or outlet) and note whether more than one valve code is stored; several at once point at the common supply or the module, not at one coil.
- If the unit has a plug-in valve relay, swap it with an identical one; if the relay is inside the module, it is bench work.
- On a one-piece unit do not open the hydraulic block or loosen brake lines to look — the valves are not serviceable from outside, and air in the system means a bleed with a scan tool afterward.
- A valve code that sets the moment the key is turned on is an electrical fault, not a driving condition: if the supply, ground and connector are good and it returns, stop there — coil, driver and the connection between them are all inside the unit.
What the lab does for a code in this family
At the bench we separate the control unit from the hydraulic block where the design allows it, test each valve coil, repair the driver circuits and the board-to-coil connections, and run every valve from the module’s own drivers before it ships back. If a coil inside the hydraulic block itself is open, we tell you before anything beyond the repair price is done.
Every repair is bench-tested and ships back with your VIN and coding on it. Sensors, switches, plug-in relays, wiring, fuses, the battery and the other modules are vehicle-side parts: a repaired module does not fix those, which is why the checks come first.
Repair options for these vehicles
- Bosch ABS / ESP 82 vehicle lines on this pageRepair from $499 · refurbished unit with your data from $950
- Time: about a week on the bench; rush repair 2–3 business days for +$100.
- Warranty: 1-year on every repair and refurbished unit. It is included with every order and starts the day we ship it back.
- Shipping: the label to us is prepaid; return Standard return shipping $29.95 (3–5 business days) · UPS 2nd Day Air return $54.95 (2 business days) · UPS Next Day Air return (overnight) $94.95 (Next business day).
- Starting prices. If the bench finds more work than your service covers, we tell you the cost and you approve it before we do it.
Related codes
Codes listed for the same vehicle lines — the ones a scan tool tends to show next to 01421.
01421 — questions
What does 01421 mean on a Audi?
On the Audi lines in our data, 01421 is listed as: High pressure valve 2. In general terms it belongs to the “Valve or solenoid circuit” family — one of the solenoid valves inside the hydraulic unit, or the circuit that drives it.
Can I drive with 01421?
With a valve fault stored the module switches ABS (and with it traction and stability control) off; the base brakes keep working. If the pedal feels different, the car pulls under braking or a wheel drags or runs hot, do not drive it — a stuck valve can hold pressure at one wheel. That is general guidance for this family of codes, not a judgment of your vehicle, which we cannot make from a code.
Is 01421 the ABS module or a sensor?
For this family of codes the module is a likely cause, but not the only one. On a valve code there is almost nothing between the module and the fault: the coil is in the hydraulic block it bolts to, the driver and the valve-relay function are on the module’s board, and the connection between them is a set of spring pins or solder joints that corrode and crack. The outside causes — low supply voltage, a bad ground, a connector pin — are quick to rule out.
How much does it cost to fix 01421?
Repair of your own module starts at $499 for the vehicles that set 01421; a refurbished unit of the same family with your data cloned onto it starts at $950. Return shipping starts at $29.95 and the label to us is prepaid; rush repair is +$100 for 2–3 business days on the bench; every repair and refurbished unit carries a 1-year warranty, from the day we ship it back. Starting prices. If the bench finds more work than your service covers, we tell you the cost and you approve it before we do it.
Will 01421 clear after the repair?
A repaired module comes back tested on the bench with your VIN and coding on it; after installation the code is cleared with a scan tool. Some vehicles still need a brake bleed, initialization or calibration after install. If the cause was on the vehicle side — a sensor, the wiring, the battery or another module — the code returns until that is fixed, which is why the checks above come first.
Which vehicles set 01421?
In our data 01421 is listed for 2 vehicle lines from Audi: 2008-2012 Audi A4 / S4 / A4 Avant (B8), 2005-2011 Audi A6 / S6 (C6). The table above gives the meaning for each line and the unit family it uses.
Still not sure?
Send us 01421, a photo of the module label and your VIN — we tell you whether the module is the likely cause and what it costs, before you pull anything. Asking costs nothing.
Repair guides
The lab
ABS Module Lab
1168 W Pioneer Parkway
Arlington, TX 76013
- Phone and text: (817) 505-4201
- Email: repairs@absmodulelab.com
- Hours: Mon–Sat 9:00 AM–7:00 PM Central
Mail-in only — ship your module to the address in your order e-mail, not to the bench.
01421 keeps coming back after the checks? Fix the module — from $499.
Look up your part number and order online — we email you a prepaid label to our lab. Or send us a photo of the label and your VIN first, and we'll tell you what you have and what it costs.
Back with your VIN and coding · can’t be repaired? repair price back, minus shipping and a $150 bench evaluation fee · 1-year warranty · rush 2–3 days +$100
Call (817) 505-4201 · 📱 Text us a photo of the module label · Confirm my module first — free · Email repairs@absmodulelab.com