ABS Module Lab

C1155

ABS / stability-control fault code, listed for 2 vehicle lines from Ford. What it means on each one, from published sources, and when the module is the cause.

What C1155 means, by vehicle

Makers reuse code numbers, so the meaning is listed per vehicle line, as its published source states it. Neutral sources (government records, parts catalogs, technical references) are linked; other sources stay on file.

VehicleMeaning of C1155Source
1999-2011 Ford RangerLeft front wheel speed sensor input circuit failureon file
2004-2006 Ford F-150 (2004-2008 body, early years)Left front wheel speed sensor input circuit failureon file

Vehicles and units that set C1155

The unit family decides the price and what ships; the part-number count is how many numbers for that line are on file for the lookup.

VehicleYearsABS unit familyRepairPart numbers
Ford Ranger1999-2011Identified on the benchFrom $49914
Ford F-150 (2004-2008 body, early years)2004-2006Bosch 5.4From $4997

Is C1155 the ABS module?

C1155 is listed for 2 vehicle lines from Ford; the meanings above fall under the “Wheel-speed sensor circuit” family of codes.

This family of codes points at one wheel’s speed-sensor circuit: the sensor itself, the two wires between it and the ABS module, the connector at each end, or the input stage inside the module that reads it. The code names the corner (left front, right rear and so on), which is the first clue — a fault that moves with the sensor when two corners are swapped is a sensor fault, and a fault that stays put at the module connector is a module fault.

Is the module the likely cause? Sometimes

For this family of codes the module is one possible cause among several. The sensor, its harness and the connector sit outside the module in salt, water and heat, so they are checked first. The module becomes the likely cause when the sensor and wiring test good at the module connector, when the same code returns on a new sensor, or when more than one wheel sets a circuit code at the same time.

Check these first

In order. The first three are the same for every ABS code; the rest are for this family. Each step is something a shop or a careful owner can do before any module comes out.

  1. Load-test the battery and measure the charging voltage; a weak or over-charging supply sets codes in every ABS family and is the cheapest thing to rule out.
  2. Check the fuses that feed the ABS module and its pump with a meter, not by eye, and clean and tighten the module’s ground strap and main power feed.
  3. Unplug the module connector and look at both halves for corrosion, water, a pushed-back or bent pin; then clear the code and note whether it returns at once, after a drive, or only under one condition.
  4. Read the code’s corner and follow that sensor’s wiring from the wheel well to its connector: chafed insulation, a cut from a rock or a tire, a connector full of mud or green corrosion.
  5. Measure the sensor — resistance across its two pins for a passive (two-wire) sensor, supply voltage at the harness for an active one — and compare it with the other wheels.
  6. With a scan tool, watch all four wheel speeds while someone drives slowly: the faulty one reads zero, drops out or lags the others.
  7. Check the tone ring, or the magnetic encoder in the wheel bearing, for cracks, missing teeth, rust packed between the teeth or a ring that has slipped.
  8. If the sensor and wiring test good back to the module connector and the code still sets, stop there: the module’s input circuit is the remaining suspect, and that is bench work.

What the lab does for a code in this family

We repair the module’s wheel-speed input circuits and the board connections behind the connector pins at the bench, and test every channel with a simulated wheel-speed signal before the module ships back.

Every repair is bench-tested and ships back with your VIN and coding on it. Sensors, switches, plug-in relays, wiring, fuses, the battery and the other modules are vehicle-side parts: a repaired module does not fix those, which is why the checks come first.

Repair options for these vehicles

Related codes

Codes listed for the same vehicle lines — the ones a scan tool tends to show next to C1155.

C1155 — questions

What does C1155 mean on a Ford?

On the Ford lines in our data, C1155 is listed as: Left front wheel speed sensor input circuit failure. In general terms it belongs to the “Wheel-speed sensor circuit” family — an open, short or missing signal on one wheel’s speed-sensor circuit.

Can I drive with C1155?

A stored wheel-speed fault can switch the ABS and stability control off — the base brakes still work, but without anti-lock help — and on some vehicles it can make the ABS activate at low speed when it should not, which feels like a pulsing pedal just before a stop. Drive gently, keep more distance and have it checked. That is general guidance for this family of codes, not a judgment of your vehicle, which we cannot make from a code.

Is C1155 the ABS module or a sensor?

For this family of codes the module is one possible cause among several. The sensor, its harness and the connector sit outside the module in salt, water and heat, so they are checked first. The module becomes the likely cause when the sensor and wiring test good at the module connector, when the same code returns on a new sensor, or when more than one wheel sets a circuit code at the same time.

How much does it cost to fix C1155?

Repair of your own module starts at $499 for the vehicles that set C1155; a refurbished unit of the same family with your data cloned onto it starts at $950. Return shipping starts at $29.95 and the label to us is prepaid; rush repair is +$100 for 2–3 business days on the bench; every repair and refurbished unit carries a 1-year warranty, from the day we ship it back. Starting prices. If the bench finds more work than your service covers, we tell you the cost and you approve it before we do it.

Will C1155 clear after the repair?

A repaired module comes back tested on the bench with your VIN and coding on it; after installation the code is cleared with a scan tool. Some vehicles still need a brake bleed, initialization or calibration after install. If the cause was on the vehicle side — a sensor, the wiring, the battery or another module — the code returns until that is fixed, which is why the checks above come first.

Which vehicles set C1155?

In our data C1155 is listed for 2 vehicle lines from Ford: 2004-2006 Ford F-150 (2004-2008 body, early years), 1999-2011 Ford Ranger. The table above gives the meaning for each line and the unit family it uses.

Still not sure?

Send us C1155, a photo of the module label and your VIN — we tell you whether the module is the likely cause and what it costs, before you pull anything. Asking costs nothing.

Repair guides

The lab

ABS Module Lab

1168 W Pioneer Parkway
Arlington, TX 76013

View on Google Maps

Mail-in only — ship your module to the address in your order e-mail, not to the bench.

C1155 keeps coming back after the checks? Fix the module — from $499.

Look up your part number and order online — we email you a prepaid label to our lab. Or send us a photo of the label and your VIN first, and we'll tell you what you have and what it costs.

Back with your VIN and coding · can’t be repaired? repair price back, minus shipping and a $150 bench evaluation fee · 1-year warranty · rush 2–3 days +$100

Call (817) 505-4201 · 📱 Text us a photo of the module label · Confirm my module first — free · Email repairs@absmodulelab.com