ABS Module Lab

66-11

ABS / stability-control fault code, listed for 1 vehicle line from Honda. What it means on each one, from published sources, and when the module is the cause.

What 66-11 means, by vehicle

Makers reuse code numbers, so the meaning is listed per vehicle line, as its published source states it. Neutral sources (government records, parts catalogs, technical references) are linked; other sources stay on file.

VehicleMeaning of 66-11Source
2009-2015 Honda Pilot (2nd gen)Pressure sensor issueson file

Vehicles and units that set 66-11

The unit family decides the price and what ships; the part-number count is how many numbers for that line are on file for the lookup.

VehicleYearsABS unit familyRepairPart numbers
Honda Pilot (2nd gen)2009-2015Honda / Acura VSA modulatorFrom $49910

What is published about failures on these lines

Is 66-11 the ABS module?

66-11 is listed for 1 vehicle line from Honda; the meanings above fall under the “Brake-pedal switch or brake-pressure sensor” family of codes.

This family of codes concerns what the module knows about the brake pedal: the brake-light (stop-lamp) switch signal that tells it the pedal is pressed, and the brake-pressure sensor that tells it how hard. The switch is a small part at the pedal; the pressure sensor is in the master cylinder or, on some units, inside the hydraulic block itself, where it is part of the module assembly. A code here means the signal is missing, stuck or out of range compared with what the module expects.

Is the module the likely cause? Sometimes

For this family of codes the module is one possible cause among several. A brake-light switch is an inexpensive, exposed part and is checked first; its code is rarely a module problem. A pressure-sensor code depends on where the sensor sits: a sensor screwed into the master cylinder is a vehicle-side part, while a sensor built into the hydraulic unit is part of the module assembly, and a code about it is bench work once the connector and supply check out.

Check these first

In order. The first three are the same for every ABS code; the rest are for this family. Each step is something a shop or a careful owner can do before any module comes out.

  1. Load-test the battery and measure the charging voltage; a weak or over-charging supply sets codes in every ABS family and is the cheapest thing to rule out.
  2. Check the fuses that feed the ABS module and its pump with a meter, not by eye, and clean and tighten the module’s ground strap and main power feed.
  3. Unplug the module connector and look at both halves for corrosion, water, a pushed-back or bent pin; then clear the code and note whether it returns at once, after a drive, or only under one condition.
  4. Check that the brake lights come on with the pedal and go off when it is released; adjust or replace a brake-light switch that is out of adjustment or sticking.
  5. With a scan tool, watch the brake-switch status and the brake-pressure reading while pressing the pedal: the switch should change state at once, and the pressure should rise smoothly and return to zero.
  6. Check the switch connector and the pressure-sensor connector for corrosion, a loose pin or brake fluid in the plug.
  7. Find out where the pressure sensor is on your vehicle — in the master cylinder or inside the ABS unit — before ordering anything.
  8. If the switch works, the sensor’s supply and connector are good and the code still sets, stop there: a sensor inside the hydraulic unit is bench work.

What the lab does for a code in this family

On units with the pressure sensor built in, we test the sensor and the module’s input stage at the bench and repair the input circuit and board connections; if the built-in sensor itself has failed, we tell you what we found and the options before anything beyond the repair price is done.

Every repair is bench-tested and ships back with your VIN and coding on it. Sensors, switches, plug-in relays, wiring, fuses, the battery and the other modules are vehicle-side parts: a repaired module does not fix those, which is why the checks come first.

Repair options for these vehicles

Related codes

Codes listed for the same vehicle lines — the ones a scan tool tends to show next to 66-11.

66-11 — questions

What does 66-11 mean on a Honda?

On the Honda line in our data, 66-11 is listed as: Pressure sensor issues. In general terms it belongs to the “Brake-pedal switch or brake-pressure sensor” family — the brake-light switch signal or the brake-pressure sensor the module reads.

Can I drive with 66-11?

A brake-switch fault can switch off cruise control and stability control and, on some vehicles, affect the shift lock; a pressure-sensor fault switches stability and brake-assist functions off. The base brakes keep working. If the brake lights do not work, fix that before driving. That is general guidance for this family of codes, not a judgment of your vehicle, which we cannot make from a code.

Is 66-11 the ABS module or a sensor?

For this family of codes the module is one possible cause among several. A brake-light switch is an inexpensive, exposed part and is checked first; its code is rarely a module problem. A pressure-sensor code depends on where the sensor sits: a sensor screwed into the master cylinder is a vehicle-side part, while a sensor built into the hydraulic unit is part of the module assembly, and a code about it is bench work once the connector and supply check out.

How much does it cost to fix 66-11?

Repair of your own module starts at $499 for the vehicles that set 66-11; a refurbished unit of the same family with your data cloned onto it starts at $950. Return shipping starts at $29.95 and the label to us is prepaid; rush repair is +$100 for 2–3 business days on the bench; every repair and refurbished unit carries a 1-year warranty, from the day we ship it back. Starting prices. If the bench finds more work than your service covers, we tell you the cost and you approve it before we do it.

Will 66-11 clear after the repair?

A repaired module comes back tested on the bench with your VIN and coding on it; after installation the code is cleared with a scan tool. Some vehicles still need a brake bleed, initialization or calibration after install. If the cause was on the vehicle side — a sensor, the wiring, the battery or another module — the code returns until that is fixed, which is why the checks above come first.

Still not sure?

Send us 66-11, a photo of the module label and your VIN — we tell you whether the module is the likely cause and what it costs, before you pull anything. Asking costs nothing.

Repair guides

The lab

ABS Module Lab

1168 W Pioneer Parkway
Arlington, TX 76013

View on Google Maps

Mail-in only — ship your module to the address in your order e-mail, not to the bench.

66-11 keeps coming back after the checks? Fix the module — from $499.

Look up your part number and order online — we email you a prepaid label to our lab. Or send us a photo of the label and your VIN first, and we'll tell you what you have and what it costs.

Back with your VIN and coding · can’t be repaired? repair price back, minus shipping and a $150 bench evaluation fee · 1-year warranty · rush 2–3 days +$100

Call (817) 505-4201 · 📱 Text us a photo of the module label · Confirm my module first — free · Email repairs@absmodulelab.com