BCM-0058
ABS / stability-control fault code, listed for 1 vehicle line from Volvo. What it means on each one, from published sources, and when the module is the cause.
What BCM-0058 means, by vehicle
Makers reuse code numbers, so the meaning is listed per vehicle line, as its published source states it. Neutral sources (government records, parts catalogs, technical references) are linked; other sources stay on file.
| Vehicle | Meaning of BCM-0058 | Source |
|---|---|---|
| 2002-2014 Volvo S60 (P2) | Power Supply Voltage too High | on file |
Vehicles and units that set BCM-0058
The unit family decides the price and what ships; the part-number count is how many numbers for that line are on file for the lookup.
| Vehicle | Years | ABS unit family | Repair | Part numbers |
|---|---|---|---|---|
| Volvo S60 (P2) | 2002-2014 | ATE / Continental MK25 | From $499 | 15 |
What is published about failures on these lines
- 2002-2014 Volvo S60 (P2): P2 brake control modules fail with no communication and ABS light on, and when the pump motor does not work or works sporadically the car logs a combination of BCM-0070/0071/0072 and BCM-C002001/C00201C/C002071
Is BCM-0058 the ABS module?
BCM-0058 is listed for 1 vehicle line from Volvo; the meanings above fall under the “Supply voltage to the module” family of codes.
This family of codes means the voltage reaching the ABS module was outside the range it works in — too low during cranking or with a weak battery, too high from a charging fault or a jump-start done wrong, or dropping out through a corroded feed. The module records it and switches itself off until the next key cycle. A supply code describes the vehicle’s electrical system as the module sees it; the module itself is one possible cause, when its own power stage or connector is at fault.
Is the module the likely cause? Sometimes
For this family of codes the module is one possible cause among several. A supply code is set by whatever the module measures at its own power pins. A battery near the end of its life, a slipping belt, a corroded battery terminal or ground strap, or a power pin that heats up under load sets it from outside. The module is the cause when the voltage at its connector is correct under load and the code still sets, which points at its internal power supply or a cracked solder joint on a power pin.
Check these first
In order. The first three are the same for every ABS code; the rest are for this family. Each step is something a shop or a careful owner can do before any module comes out.
- Load-test the battery and measure the charging voltage; a weak or over-charging supply sets codes in every ABS family and is the cheapest thing to rule out.
- Check the fuses that feed the ABS module and its pump with a meter, not by eye, and clean and tighten the module’s ground strap and main power feed.
- Unplug the module connector and look at both halves for corrosion, water, a pushed-back or bent pin; then clear the code and note whether it returns at once, after a drive, or only under one condition.
- Measure voltage at the module’s power pins with the key on and while cranking, and compare it with the battery — a difference under load means resistance in the feed, fuse box or connector.
- Check the fuse-box terminals for heat marks; a fuse holder that has overheated drops voltage under the pump’s load.
- Ask when the code first appeared — right after a jump-start, a battery change or welding on the vehicle points at an event, not a fault, and the code may not return.
- If the voltage at the module connector is correct under load and the code keeps returning, stop there: the module’s internal power stage is the remaining suspect.
What the lab does for a code in this family
At the bench we run the module from a controlled supply, test it at the low and high ends of its range and under the pump’s load, and repair the internal power supply, the power-pin solder joints and the components that fail from an over-voltage event. A repaired module will not survive a charging fault that is still on the vehicle.
Every repair is bench-tested and ships back with your VIN and coding on it. Sensors, switches, plug-in relays, wiring, fuses, the battery and the other modules are vehicle-side parts: a repaired module does not fix those, which is why the checks come first.
Repair options for these vehicles
- ATE / Continental MK251 vehicle line on this pageRepair from $499 · refurbished unit with your data from $950
- Time: about a week on the bench; rush repair 2–3 business days for +$100.
- Warranty: 1-year on every repair and refurbished unit. It is included with every order and starts the day we ship it back.
- Shipping: the label to us is prepaid; return Standard return shipping $29.95 (3–5 business days) · UPS 2nd Day Air return $54.95 (2 business days) · UPS Next Day Air return (overnight) $94.95 (Next business day).
- Starting prices. If the bench finds more work than your service covers, we tell you the cost and you approve it before we do it.
Related codes
Codes listed for the same vehicle lines — the ones a scan tool tends to show next to BCM-0058.
- BCM-00701 shared vehicle linePump motor, motor relay or relay circuit
- BCM-00711 shared vehicle lineOther system-level codes
- BCM-00721 shared vehicle lineOther system-level codes
- BCM-C0020011 shared vehicle lineOther system-level codes
- BCM-C00201C1 shared vehicle linePump motor, motor relay or relay circuit
- BCM-C0020711 shared vehicle lineOther system-level codes
- BCM-00521 shared vehicle lineControl module internal fault
- BCM-00741 shared vehicle lineValve or solenoid circuit
BCM-0058 — questions
What does BCM-0058 mean on a Volvo?
On the Volvo line in our data, BCM-0058 is listed as: Power Supply Voltage too High. In general terms it belongs to the “Supply voltage to the module” family — battery or ignition voltage at the ABS module reads too low or too high.
Can I drive with BCM-0058?
A supply fault switches ABS and stability control off, and the same weak battery or charging fault can leave you stranded. Fix the electrical cause first; if the red brake warning light is also on, have the vehicle checked before driving it. That is general guidance for this family of codes, not a judgment of your vehicle, which we cannot make from a code.
Is BCM-0058 the ABS module or a sensor?
For this family of codes the module is one possible cause among several. A supply code is set by whatever the module measures at its own power pins. A battery near the end of its life, a slipping belt, a corroded battery terminal or ground strap, or a power pin that heats up under load sets it from outside. The module is the cause when the voltage at its connector is correct under load and the code still sets, which points at its internal power supply or a cracked solder joint on a power pin.
How much does it cost to fix BCM-0058?
Repair of your own module starts at $499 for the vehicles that set BCM-0058; a refurbished unit of the same family with your data cloned onto it starts at $950. Return shipping starts at $29.95 and the label to us is prepaid; rush repair is +$100 for 2–3 business days on the bench; every repair and refurbished unit carries a 1-year warranty, from the day we ship it back. Starting prices. If the bench finds more work than your service covers, we tell you the cost and you approve it before we do it.
Will BCM-0058 clear after the repair?
A repaired module comes back tested on the bench with your VIN and coding on it; after installation the code is cleared with a scan tool. Some vehicles still need a brake bleed, initialization or calibration after install. If the cause was on the vehicle side — a sensor, the wiring, the battery or another module — the code returns until that is fixed, which is why the checks above come first.
Still not sure?
Send us BCM-0058, a photo of the module label and your VIN — we tell you whether the module is the likely cause and what it costs, before you pull anything. Asking costs nothing.
Repair guides
The lab
ABS Module Lab
1168 W Pioneer Parkway
Arlington, TX 76013
- Phone and text: (817) 505-4201
- Email: repairs@absmodulelab.com
- Hours: Mon–Sat 9:00 AM–7:00 PM Central
Mail-in only — ship your module to the address in your order e-mail, not to the bench.
BCM-0058 keeps coming back after the checks? Fix the module — from $499.
Look up your part number and order online — we email you a prepaid label to our lab. Or send us a photo of the label and your VIN first, and we'll tell you what you have and what it costs.
Back with your VIN and coding · can’t be repaired? repair price back, minus shipping and a $150 bench evaluation fee · 1-year warranty · rush 2–3 days +$100
Call (817) 505-4201 · 📱 Text us a photo of the module label · Confirm my module first — free · Email repairs@absmodulelab.com