ABS Module Lab

C2402

ABS / stability-control fault code, listed for 8 vehicle lines from Hyundai, Kia. What it means on each one, from published sources, and when the module is the cause.

What C2402 means, by vehicle

Makers reuse code numbers, so the meaning is listed per vehicle line, as its published source states it. Neutral sources (government records, parts catalogs, technical references) are linked; other sources stay on file.

VehicleMeaning of C2402Source
2007-2012 Hyundai Santa Fe (CM)Pump motor electrical fault: motor relay fault, motor power circuit open or shorted, or motor lockedon file
2010-2015 Hyundai Tucson (LM / ix35)Pump motor failure: motor relay or fuse open, open or short in the motor, or motor lockon file
2011-2015 Hyundai Elantra (MD sedan, JK coupe)Pump motor failure: motor relay or fuse open, open or short in the motor, or motor lockon file
2013-2018 Hyundai Santa Fe (DM, 3-row)Motor pump error: the motor power line is normal but no signal is detected on the motor monitor line; causes include wiring or connector, a poor ground or the HECUon file
2010-2013 Kia Soul (AM)ABS pump motor voltage fault: motor relay or fuse open, open or short in the motor, or motor lockon file
2011-2015 Kia Optima (TF, gasoline)ABS pump motor voltage fault: motor relay or fuse open, open or short in the motor, or motor lockon file
2011-2015 Kia Sorento (XM)ABS pump motor voltage fault: motor relay or fuse open, open or short in the motor, or motor lockon file
2016-2021 Kia Sportage (QL)ABS pump motor voltage fault: motor relay or fuse open, open or short in the motor, or motor lockon file

Vehicles and units that set C2402

The unit family decides the price and what ships; the part-number count is how many numbers for that line are on file for the lookup.

VehicleYearsABS unit familyRepairPart numbers
Hyundai Santa Fe (CM)2007-2012Bosch ABS / ESP 8From $4997
Hyundai Tucson (LM / ix35)Recall listed — check your VIN first2010-2015Mando ABS / ESCFrom $4992
Hyundai Elantra (MD sedan, JK coupe)Recall listed — check your VIN first2011-2015Mando ABS / ESCFrom $4993
Hyundai Santa Fe (DM, 3-row)Recall listed — check your VIN first2013-2018Mando ABS / ESCFrom $4992
Kia Soul (AM)Recall listed — check your VIN first2010-2013Mando ABS / ESCFrom $4997
Kia Optima (TF, gasoline)Recall listed — check your VIN first2011-2015Mando ABS / ESCFrom $4992
Kia Sorento (XM)Recall listed — check your VIN first2011-2015Mando ABS / ESCFrom $4993
Kia Sportage (QL)Recall listed — check your VIN first2016-2021Mando ABS / ESCFrom $4992

What is published about failures on these lines

Is C2402 the ABS module?

C2402 is listed for 8 vehicle lines from Hyundai and Kia; the meanings above fall under the “Pump motor, motor relay or relay circuit” family of codes.

This family of codes concerns the pump motor that builds pressure inside the ABS unit, the relay or driver that switches it, and the circuit between them. The module runs the pump for a moment at start-up and watches for current and for the motor’s feedback; no current, too much current, or a motor that does not stop sets a code here. On some units the pump or valve relay is a separate plug-in part you can swap; on others the relay function is a solid-state driver inside the module, so a “relay” code is really a module code there.

Is the module the likely cause? Often

For this family of codes the module is a likely cause, but not the only one. The relay or driver that feeds the pump sits inside the module on many units, and its solder joints and driver transistors carry the pump’s full current — a pump that runs constantly with the key off, or a relay code that returns as soon as it is cleared, points there. A seized or worn pump motor, a blown pump fuse and a corroded power or ground feed can set the same code from outside the module, so those are checked first.

Check these first

In order. The first three are the same for every ABS code; the rest are for this family. Each step is something a shop or a careful owner can do before any module comes out.

  1. Load-test the battery and measure the charging voltage; a weak or over-charging supply sets codes in every ABS family and is the cheapest thing to rule out.
  2. Check the fuses that feed the ABS module and its pump with a meter, not by eye, and clean and tighten the module’s ground strap and main power feed.
  3. Unplug the module connector and look at both halves for corrosion, water, a pushed-back or bent pin; then clear the code and note whether it returns at once, after a drive, or only under one condition.
  4. With the module connector unplugged, look for heat-darkened or loose pins on the heavy pump-motor terminals — the pump draws a lot of current, and a tired pin or fuse holder drops voltage under that load.
  5. Listen: a pump that runs with the key off, or hums constantly, is a relay or driver stuck on — pull the pump fuse or disconnect the battery so it does not drain the battery or burn the motor out.
  6. If the unit has a plug-in pump or valve relay, swap it with an identical relay and see whether the code stays.
  7. With a scan tool, command the pump on (where the tool allows it) and listen and feel for it running; no response with good power and ground points at the module or the motor.
  8. If the fuse, power, ground and connector are good and the code returns, stop there — the rest is inside the unit and is bench work.

What the lab does for a code in this family

At the bench we load the module’s pump-motor driver the way the motor does, repair the driver circuit, its solder joints and the board-to-motor connections, and test a driver that will not switch off. We repair the electronics only: a pump motor that is worn or seized, or the hydraulic block, is not something we repair, and we tell you when the bench points there.

Every repair is bench-tested and ships back with your VIN and coding on it. Sensors, switches, plug-in relays, wiring, fuses, the battery and the other modules are vehicle-side parts: a repaired module does not fix those, which is why the checks come first.

Repair options for these vehicles

Related codes

Codes listed for the same vehicle lines — the ones a scan tool tends to show next to C2402.

C2402 — questions

What does C2402 mean on a Hyundai?

On the Hyundai lines in our data, C2402 is listed as: Pump motor failure: motor relay or fuse open, open or short in the motor, or motor lock. In general terms it belongs to the “Pump motor, motor relay or relay circuit” family — the ABS pump motor, the relay that feeds it, or a pump that runs when it should not. Kia lists the same number with its own wording — see the meaning-by-vehicle table.

Can I drive with C2402?

A pump fault switches ABS and stability control off while the base brakes keep working; a pump that runs constantly can drain the battery overnight and overheat the motor, so pull its fuse or disconnect the battery until it is looked at. On a hybrid or electro-hydraulic brake unit the pump is the brake booster — treat a pump code there as a do-not-drive until it is checked. That is general guidance for this family of codes, not a judgment of your vehicle, which we cannot make from a code.

Is C2402 the ABS module or a sensor?

For this family of codes the module is a likely cause, but not the only one. The relay or driver that feeds the pump sits inside the module on many units, and its solder joints and driver transistors carry the pump’s full current — a pump that runs constantly with the key off, or a relay code that returns as soon as it is cleared, points there. A seized or worn pump motor, a blown pump fuse and a corroded power or ground feed can set the same code from outside the module, so those are checked first.

How much does it cost to fix C2402?

Repair of your own module starts at $499 for the vehicles that set C2402; a refurbished unit of the same family with your data cloned onto it starts at $950. Return shipping starts at $29.95 and the label to us is prepaid; rush repair is +$100 for 2–3 business days on the bench; every repair and refurbished unit carries a 1-year warranty, from the day we ship it back. Starting prices. If the bench finds more work than your service covers, we tell you the cost and you approve it before we do it.

Will C2402 clear after the repair?

A repaired module comes back tested on the bench with your VIN and coding on it; after installation the code is cleared with a scan tool. Some vehicles still need a brake bleed, initialization or calibration after install. If the cause was on the vehicle side — a sensor, the wiring, the battery or another module — the code returns until that is fixed, which is why the checks above come first.

Which vehicles set C2402?

In our data C2402 is listed for 8 vehicle lines from Hyundai and Kia: 2011-2015 Hyundai Elantra (MD sedan, JK coupe), 2007-2012 Hyundai Santa Fe (CM), 2013-2018 Hyundai Santa Fe (DM, 3-row), 2010-2015 Hyundai Tucson (LM / ix35) and 4 more. The same number can mean something different on each make, so the table above gives the meaning per vehicle.

Still not sure?

Send us C2402, a photo of the module label and your VIN — we tell you whether the module is the likely cause and what it costs, before you pull anything. Asking costs nothing.

Repair guides

The lab

ABS Module Lab

1168 W Pioneer Parkway
Arlington, TX 76013

View on Google Maps

Mail-in only — ship your module to the address in your order e-mail, not to the bench.

C2402 keeps coming back after the checks? Fix the module — from $499.

Look up your part number and order online — we email you a prepaid label to our lab. Or send us a photo of the label and your VIN first, and we'll tell you what you have and what it costs.

Back with your VIN and coding · can’t be repaired? repair price back, minus shipping and a $150 bench evaluation fee · 1-year warranty · rush 2–3 days +$100

Call (817) 505-4201 · 📱 Text us a photo of the module label · Confirm my module first — free · Email repairs@absmodulelab.com