ABS Module Lab

U0121 and an ABS Module With No Communication: Causes and Repair

ABS Module Lab Team · · 22 min read

What U0121, U0415 and Ford's U3000:49 mean, the vehicles where a silent ABS module is a known failure, the checks to run first and what to ship.

A technician's hands probing the pins of a wiring harness connector in an engine bay with red and black multimeter test leads while a small light shines on the connector.

U0121 is stored by the engine, body or instrument modules when they stop hearing from the ABS module, and a scan tool that cannot reach the ABS module is the same fault seen from the diagnostic port. The module itself may have failed, or it may have lost its fuse, power, ground, connector or network wiring, so check those first. An ABS module that has power and ground and still will not talk is repaired here from $499 ($325 for a Kelsey-Hayes EBC325), or replaced with a refurbished unit carrying your data from $950.

The short answer

U0121 means lost communication with the anti-lock brake system control module: another module stopped receiving its messages, so the code describes a silence, not its cause. U0415 means the ABS module still talks but sends invalid data, and Ford's U3000:49 and U3000:41, which many scan tools print as U3000-49 and U3000-41, are filed as control module faults. Before you blame the module, confirm that the scan tool reaches other modules, then check the ABS fuses, battery voltage, power and ground at the module connector, the connector pins and the network wires. With all of those good, a module that stays silent has most likely failed inside: no communication is a known module failure on 41 vehicle lines on file, and U0121 or a maker's own lost-communication code is on file for 18 more. Repair starts at $499 ($325 for a Kelsey-Hayes EBC325) and returns your own module with its coding.

What U0121 and a no-communication ABS module mean

The modules in a modern vehicle talk over shared networks, and on many vehicles several of them rely on the ABS module's messages, wheel speed among them. When those messages stop, the modules that expect them log a lost-communication code against it: U0121, Lost Communication With Anti-Lock Brake System (ABS) Control Module. That is why U0121 sits in the engine, body or instrument module rather than in the ABS module, and why it says nothing about the reason for the silence.

From the driver's seat the result is usually the ABS, traction and stability lamps together, and on 14 of the lines on file a dead speedometer as well, since on many vehicles the speed signal comes from the ABS module. The K2 trucks, the 2008–2012 Escape, the Tiguan, both MINI lines, the Boxster and the Cayenne are among them.

The codes on file

Code Where on file Meaning on file What it points to
U0121 Chrysler, Dodge, Jeep, Ram, GM, F-150, Genesis, Mazda3 and LR4 lines Lost communication with the ABS module The ABS module has gone quiet
U0415 Grand Cherokee WK2 Invalid data from the ABS module The ABS module talks, but its data fails
U3000:49, U3000:41 Escape, Explorer, Expedition, Focus, Fusion Control module fault A fault the ABS module reports in itself
01316:013, U101700 A3 8P, Q7 4L, Golf and Jetta Mk5-Mk6 ABS control module, no signal or communication The ABS module has gone quiet
5DF5 BMW E60 and E90 groups No communication or internal fault The ABS module, silent or failed inside
BCM-0108 Volvo P2 Communication fault between control units Either end of the link
U0073 Camry XV40 Control module communication bus off The module's own bus link
86-14, U0155, 86 Accord, CR-V F-CAN network fault; 86-14 and U0155 name the gauge control module The network or the gauge side, heard by the VSA unit
C1611 Optima, Sorento, Soul, Sportage No valid CAN message from the engine ECU for about 500 ms; engine control module or HECU The engine computer, or the HECU itself
C24DB Mercedes SBC CAN fault, typically mismatched part numbers after a unit swap A unit that does not match
U3000-49, U0416-68, U3006-16 Civic, 2016–2021 Internal software problem; VSA system malfunction; low ECU supply voltage Software, the unit or its supply

Read the last column first. U0121, 01316:013, U101700 and 5DF5 mean the ABS module went quiet, but C1611 on the Kias and 86-14 or U0155 on the Accords are the ABS or VSA unit itself reporting that it cannot hear the engine computer or the gauge cluster, so the other module is a suspect too. On a 2016–2017 Civic other than the 5-door, Honda bulletin 17-007 ties U3000-49, with a blinking brake lamp and an electric parking brake message, to a software problem inside the modulator-control unit that a software update cures.

Vehicles where no communication is a known module failure

The failure record of 41 lines below names no communication with the module, or loss of communication. Of the other 30, 18 carry U0121 or a maker's lost-communication code, three Fords carry only U3000:49 and U3000:41, the 2016–2021 Civic carries U3000-49 with its software and supply codes, and eight carry a network code that the ABS, VSA or SBC unit logs itself. The unit column follows the record; where it names no supplier, the label on the module decides, and you can check its number in the part-number lookup.

Chrysler, Dodge, Jeep and Ram

Vehicle line Years Unit on file What the record shows
300, Charger, Challenger, Magnum (LX) 2005–2020 Supplier not named U0121
Grand Caravan and Town & Country 2008–2020 Supplier not named U0121
Journey 2009–2020 MK61 (Continental) U0121, filed as a module fault code
Compass (MK49), Patriot (MK74) 2007–2017 Filed under MK60 / MK61 U0121
Grand Cherokee WK 2005–2010 MK25e (Continental Teves) U0121; no communication with the ABS control module
Grand Cherokee WK2 2011–2021 ZF U0121 and U0415
Liberty KJ 2002–2007 Filed under MK70 U0121
Wrangler JK 2007–2018 MK61 (Continental) U0121
Ram 1500 DR 2002–2008 Kelsey-Hayes to 2005, then TRW No communication on the 2006–2008 TRW units
Ram 1500 DS and Classic 2009–2018 TRW, EBC-440 named U0121
Ram 1500 DT 2019–2020 Continental U0121; recall 24V-653

The Grand Caravan, the LX cars, the WK2 and the Ram 1500 DT have no catalog family and take the any-make repair, while the Wrangler JK, Compass, Patriot and Journey repair under the MK60 / MK61 family. On the Ram 1500 DT, recall 24V-653 describes an ABS module software condition that can switch stability control off and light the ABS, ESC, adaptive cruise and forward collision lamps at start-up, and the dealer's software update is the fix. The Grand Caravan and Town & Country guide covers the vans, the Ram 2500 and 3500 guide the heavy-duty Rams, and the internal codes these lines also store are in the internal-failure code guide.

GM

Vehicle line Years Unit on file What the record shows
GMT900 Silverado and Sierra 1500, Tahoe, Suburban, Yukon, Avalanche, Escalade 2007–2014 Bosch 8.0 U0121
K2 trucks and SUVs 2014–2019 Supplier not named No communication, all ABS lamps on, dead speedometer, pump not running
GMT900 2500HD and 3500HD 2007–2014 TRW EBC-345; EBC-440 on JL4 trucks No communication, pump stuck on, intermittent operation, pump codes
Impala and Impala Limited 2006–2016 TRW EBC-440 No communication, pump stuck on, intermittent operation, pump codes, C0550
Malibu (Epsilon) 2008–2012 TRW EBC-440 No communication, pump stuck on, intermittent operation, pump codes, C0550
Express and Savana vans 2003–2017 TRW EBC-345 / EBC-440 (Savana from 2008) No communication, pump stuck on, intermittent operation, pump codes

The TRW units come off the valve body on their own, so only the module ships, and the TRW EBC family page prices them. The K2 has no supplier named and takes the any-make repair.

Ford, Lincoln, Mercury and Mazda

Vehicle line Years Unit on file What the record shows
Escape, Mariner, Tribute 2008–2012 MK61 U3000:49, U3000:41; no communication, dead speedometer
Explorer and Sport Trac, Mountaineer 2002–2010 MK61 from 2004 U3000:49, U3000:41; no communication
Explorer 2011–2019 MK100 U3000:49, U3000:41; lost communication, dead speedometer
Expedition and EL, Navigator 2007–2017 MK61 through 2014 U3000:49, U3000:41
Focus, North American 2005–2011 Supplier not named U3000:49, U3000:41
Fusion 2006–2012 Supplier not named U3000:49, U3000:41
F-150 and Mark LT 2007–2014 Bosch 8.0 with stability control U0121
E-150 to E-450 Econoline 2000–2014 TRW on 2009–2014 No communication, pump stuck on, intermittent operation, pump codes
F-250 and F-350 Super Duty 2005–2016 TRW EBC-345, then EBC-450 No communication, pump stuck on, intermittent operation, pump codes
Mustang S197 2005–2014 TRW EBC-450 on 2010–2014 No communication, pump stuck on, intermittent operation, pump codes
Mazda3 (BK, BL) 2004–2013 MK70 on 2004–2009 BK cars U0121

The Escape and Explorer records pair the lost communication with B1342 and a pump code, and the Escape record adds no braking effort at one or more wheels; the MK100 lines repair under the MK100 family.

Volkswagen and Audi

Vehicle line Years Unit on file What the record shows
A3 8P 2006–2013 MK61 01316:013, U101700
A3 and S3 8V, TT 8S 2015–2020 MK100, 46-pin No communication; parking brake that sticks or will not engage
A4, allroad, A5 (B9), A6, A7, Q5, Q7 2016–2020 Bosch 9.0 No communication, invalid data from the module
A4 and S4 B8, A5, S5, Q5 2008–2012 Bosch 8.0 Loss of communication
A4 and S4 B6/B7, A6 C5, A8 D3 2002–2008 Bosch 5.7; B7 also Bosch 8.0 Loss of communication
A6 and S6 C6, A8 2005–2011 Bosch 8.0 No communication
Q7 4L 2007–2015 MK60E / MK61 01316:013
TT 8N 2000–2006 MK20 on 2000–2002 cars No communication, dead speedometer
Golf and Jetta Mk4, New Beetle 1998–2006 MK20 IE; MK60 with ESP No communication on the MK60 cars, dead speedometer
Golf, Jetta, Eos, Beetle (Mk5, Mk6) 2006–2018 MK60, MK61 from 2009 01316:013, U101700
Passat B5 and B5.5 1998–2005 Bosch 5.3, later 5.7 Loss of communication
Tiguan 5N 2009–2020 Not named to 2017; MK100 from 2018 No communication, dead speedometer

These cars report the silence in their own style, 01316:013 and U101700, and the Bosch lines name loss of communication among their failures. The VW and Audi MK60 guide covers the ATE cars.

BMW and MINI

Vehicle line Years Unit on file What the record shows
5 Series E39, 7 Series E38 1998–2003 Bosch 5.7 Communication issues, dead speedometer
X5 E53 2000–2006 Bosch 5.7; Bosch 8.0 on late cars Loss of communication
5 Series E60 and E61, 6 Series 2004–2010 Bosch 8.0; MK60E on the M5 and M6 5DF5
3 Series E90 to E93, 1 Series, Z4 2006–2013 MK60E / MK61 5DF5
3, 4 and 2 Series (F30, F32, F22) 2014–2019 MK100 No communication
X3 F25, X4 F26 2011–2018 Supplier not named No communication
MINI R50, R52, R53 2002–2008 MK60 No communication, dead speedometer
MINI R55, R56, R57 2007–2015 TRW No communication, dead speedometer

5DF5 is filed as no communication or an internal fault, so a BMW that sets it gets the same power and ground checks before the module is pulled.

Mercedes-Benz, Land Rover, Jaguar, Porsche and Volvo

Vehicle line Years Unit on file What the record shows
Mercedes C-Class W203, CLK W209 2001–2007 MK25 Loss of communication; P2068, P20CC, P2036
Mercedes ML W164, GL, R-Class 2006–2012 MK25 No communication, dead speedometer
Mercedes ML/GLE W166, GL/GLS 2012–2019 Supplier not named Communication issues, dead speedometer
Mercedes E-Class W211, CLS, SL (SBC) 2003–2012 Bosch SBC C24DB; quoted first
LR3, Range Rover Sport L320 2005–2009 Bosch 8.0 Loss of communication
LR4, Range Rover, Range Rover Sport, LR2 2008–2020 Bosch 8.0 on 2010–2012; MK61 on the LR2 Loss of communication; U0121
Range Rover L322 2002–2009 Bosch 5.7 Loss of communication
Jaguar XF X250 2013–2020 Bosch named for the F-Type and XJR No communication, dead speedometer
Boxster 986, 911 996 1997–2004 Bosch 5.7 No communication, dead speedometer
Cayenne 955 and 957 2003–2006 ATE; MK25-type on the 955 No communication, dead speedometer
Volvo P2 S60, S80, V70, XC70, XC90 2002–2014 MK25 / MK25E No communication; BCM-0108
Volvo early P2 and P80 1998–2004 MK20 Cracked solder: false sensor codes or lost communication

On the W203 and W209, the stored codes P2068, P20CC and P2036 report no or incorrect messages from the N47-5 ESP control unit; the brake light switch, which can light the BAS, ESP and ABS lamps by itself on cars such as the C240, comes first. C24DB on an SBC car typically means a unit with mismatched part numbers after a swap, and SBC work is quoted first. The early P2 Volvos can lose communication through cold solder joints around the terminals, and failed ABS pump drivers are named as well.

Honda, Hyundai, Kia, Toyota and Subaru

Vehicle line Years Unit on file What the record shows
Accord, 8th generation 2008–2012 Nissin VSA modulator 86-14
Accord, 9th generation 2013–2017 Nissin VSA modulator 86-14, U0155
Civic, 10th generation 2016–2021 MK100 U3000-49 (software), U0416-68, U3006-16
CR-V, 3rd generation 2007–2011 VSA modulator assembly 86
Genesis, Genesis Coupe, Equus 2009–2016 MK61 U0121
Kia Optima TF 2011–2015 Mando HECU C1611; recall 23V-652
Kia Sorento XM 2011–2015 Mando C1611; recall 23V-652
Kia Soul AM 2010–2013 Mando C1611; recall 23V-652
Kia Sportage QL, Cadenza 2016–2021 Mando HECU C1611; recall 21V-137
Camry XV40 2007–2011 Bosch ABS 8.1 U0073; lost communication
Legacy BL, Outback BP 2005–2009 Bosch 5.7 No communication, or sensor codes that stay after new sensors

On the Kias, C1611 means the HECU heard nothing valid from the engine computer for about 500 ms, and the record names the engine control module or the HECU as the cause, so test both; the same four lines have HECU fire recalls 23V-652 and 21V-137 on file, remedied with fuses and, on some Sportages, software. The XV40 Camry's Bosch 8.1 loses communication when fine internal wires come loose from its circuit board, which also gives intermittent gauges and warning lamps.

Check these before you condemn the module

Work from the outside in, because every step below costs less than a module.

  1. Does the scan tool reach anything? If no module answers, suspect the tool, the diagnostic connector or the network itself. If the engine and body modules answer and only the ABS module does not, carry on down the list.
  2. Battery and charging voltage. A battery that sags during cranking or a weak charging system can knock modules off the network; on the 2016–2021 Civic, U3006-16 names low 12 V battery voltage and loose terminals at the modulator.
  3. Fuses. Find the ABS module's fuses in the owner's manual or the wiring diagram; on many vehicles there is a high-current pump fuse and at least one smaller feed for the electronics. Test each on both sides with the key on. On the Kias with recalls 23V-652 and 21V-137 on file, the fuse is the recall's remedy: until it is fitted, park outside, as the Optima recall advises, and do not fit a larger fuse.
  4. Power and ground at the connector. Disconnect the battery, unplug the module and reconnect the battery; then, key on, check battery and ignition voltage at the feed pins and test the ground pin against the battery negative with a test light or under load, since a meter alone can pass a corroded ground.
  5. The connector. Look for water, green corrosion, pushed-back or spread pins and a broken lock; the MK100 unit on the A3 8V has a 46-pin connector, and one bent pin is enough.
  6. The network wires. Check the network wiring between the module connector and the rest of the network for opens and shorts; on a CAN network that is a twisted pair of wires. A shop can also measure bus resistance at the diagnostic connector with the battery disconnected and compare it with the service information; on many high-speed CAN networks it reads about 60 ohms.
  7. The other module. When the ABS or VSA unit is the one reporting the loss (C1611, 86-14, U0155), check the engine computer or the gauge cluster as well.
  8. Recalls and bulletins. Run the VIN at nhtsa.gov/recalls and ask a dealer about software bulletins, the Ram 1500 DT and the 2016–2017 Civic among them.

When every check passes and the ABS module still will not answer, the fault is most likely inside it, and that is where the repair here starts; the order form has an answer for a scan tool that cannot connect to the ABS module. If the pedal feels different, the red brake warning is on or water has been in the vehicle, have a mechanic look before driving further.

Repair, refurbished, used or new: what each really costs

Option Starting at What comes back Before you buy
Repair of the module you have $499; $325 for a Kelsey-Hayes EBC325 Your module, the cause of the silence found and fixed on the board, coding as it was Confirm power, ground and network first
Refurbished unit with your data $950 A same-family unit, bench-tested, carrying the data read from your original, which stays here as the core with no added charge Ship the original first
Used module No price on file Someone else's coding and an unknown past The installer decides what setup it needs
New dealer module The catalog price for your number A new unit The installer can say whether it needs programming and what that costs
SBC or hybrid unit Quoted first A quote before any work Nothing until the quote

Each price is a starting price, and extra work found on the bench is quoted to you and done only once you approve it. A standard job spends about a week on the bench; rush repair, at +$100, cuts bench time to 2–3 business days. Return shipping is picked at checkout: $29.95 standard, $54.95 for two-day UPS or $94.95 for next-day UPS. The lab pays for the label that brings the module in and emails it once you have paid, and $55 changes it from USPS ground to UPS 2nd Day Air. The 1-year warranty is part of every repair and refurbished unit, and the warranty page explains it.

A module the bench cannot save puts the job on hold until you choose between a refurbished unit for the price difference and your module sent back with the repair price refunded, shipping costs and a $150 bench evaluation fee deducted. Because the refurbished unit takes its data from your original module, nothing ships to you before your module arrives. Order the any-make repair through start a repair, find each family's price on the pricing page, or send the label photo first through request a quote.

Removing and shipping the module

Disconnect the battery before you unplug the module, and if a step needs tools or skills you do not have, let a shop remove it. Never drive with a brake line open, and expect a brake bleed whenever a line has been disconnected.

What comes out depends on the unit:

  • Kelsey-Hayes and TRW EBC modules, on the GM, Ford, Ram and MINI lines in the tables that carry them: the module comes off the valve body by itself and the brake lines stay on the vehicle.
  • Bosch and ATE units: the control unit sits on the valve block and on many units unbolts, leaving the lines in place; send a photo if you are not sure.
  • One-piece units, Honda's VSA modulator and the Toyota and Nissan actuators: pump, valves and control unit come out together, so cap every port as it is opened.
  • No unit family on file, as on the K2, Grand Caravan, LX cars, WK2, Ram 1500 DT, X3 F25 and W166: ask first through the quote form with a label photo.
  1. Photograph the label before anything else. A module that will not communicate cannot be identified by a scan tool, so its label is where the part number comes from.
  2. Release the connector lock fully, then pull straight; a forced connector can crack.
  3. Remove the module or the unit as described above, keeping a unit that holds brake fluid upright.
  4. Pack it. Bag the module, cushion it on all sides in a sturdy box, and write the RMA number on the box and on a note inside, as the mail-in instructions describe.
  5. Ship it on the prepaid label that arrives by email after payment; status emails follow, and how it works covers the bench steps.

After it is back in the car

Plug the module in, reconnect the battery and check communication before anything else: the scan tool should now reach the ABS module. Clear the codes in every module, the U0121 entries in the engine, body and instrument modules included, then drive until all four wheels have turned at speed and the lamps go out. Your coding comes back on a repaired module and goes onto a refurbished one; past that, the vehicle maker's installation procedure governs: some vehicles still need a brake bleed, initialization or calibration after install, whichever the procedure calls for. If U0121 comes back while the module now answers, its connector, ground or network wiring is the next suspect.

FAQ

What does U0121 mean?

U0121 is Lost Communication With Anti-Lock Brake System (ABS) Control Module, logged by a module on the network, such as the engine, body or instrument module, when the ABS module's messages stop. The ABS module may have failed, or it may have lost its fuse, power, ground, connector or network wiring. If the ABS module has power, ground and a sound connector and still will not answer a scan tool, the module itself is the likely repair.

Can I drive with a U0121 code?

A vehicle with U0121 still brakes normally on a conventional system, but anti-lock braking, traction control and stability control are off, and on some lines on file the speedometer stops too. Drive gently and have it diagnosed soon. Stop driving if the red brake warning comes on or the pedal feels different.

Can a bad battery cause U0121?

A battery that drops voltage while cranking, a weak alternator or a loose battery terminal can make the ABS module fall off the network and leave U0121 in the other modules. The 2016–2021 Honda Civic's record names low 12 V battery voltage and loose terminals at the modulator as causes of U3006-16, its power-source code. Test the battery and charging system before removing anything.

Why can't my scan tool communicate with the ABS module?

A scan tool cannot reach the ABS module when the module has lost its fuse, power, ground or network wiring, when its connector is damaged, or when the module has failed inside. If the tool also cannot reach the engine or body modules, look at the tool, the diagnostic connector and the network first. If only the ABS module is silent and its power, ground, connector and network wiring test good, the module itself has most likely failed, and repair here starts at $499.

What does U0415 mean?

U0415 means invalid data received from the ABS module: the module is still on the network, but what it sends fails the other modules' checks. On file it appears on the 2011–2021 Jeep Grand Cherokee (WK2), alongside U0121. Check the module's power, ground and connector before suspecting the module itself.

What is U3000-49 on a Ford?

Ford writes it U3000:49 and many scan tools print U3000-49; on file it is an ABS control module fault on the 2008–2012 Escape, both Explorer generations, the Expedition and Navigator, the Focus and the Fusion, alongside U3000:41. The 2002–2010 Explorer record lists it with B1342, no communication with the ABS module and a pump-motor circuit failure. On a 2016–2017 Honda Civic other than the 5-door, U3000-49 is a software fault that a software update fixes.

Can a no-communication ABS module be repaired?

An ABS module that will not communicate can be repaired when the fault is inside it, and the records on file describe two such faults: fine wires that come loose from the board in the XV40 Camry's Bosch 8.1, and cracked solder around the terminals on early P2 Volvos. The bench powers the module, finds why it is silent and repairs it at component level. If it is past repair, you choose between a refurbished unit for the price difference and having your module shipped back, with the repair price returned minus shipping and a $150 bench evaluation fee.

Will the speedometer work again after the ABS module is fixed?

On vehicles whose speedometer died when the ABS module went silent, such as the 2014–2019 K2 trucks, the 2008–2012 Escape and the MINI R56, the speedometer should return once the module is back on the network. If it does not, the instrument cluster and the network wiring are next to check.

How much does it cost to fix U0121?

Fixing U0121 can cost no more than a fuse, a cleaned ground or a repaired connector, and an open recall can make the fix free, so check those and the VIN first. When the ABS module itself has failed, our repair is from $499 ($325 on a Kelsey-Hayes EBC325) and a refurbished replacement carrying your data is from $950, with return shipping on top.

Sources